- FEATURES
- SPECIFICATIONS
- OPTIONS
Get higher benching and smoother lift.
FEATURES:
- 60" front lift height for higher benching
- Improved front slide
- Spring-loaded outer lift arm
- 12 and 14 ft. models available
- Reduced moldboard interference
- Hydraulically elevated rear slide arm available
- Hydraulically telescoping push arm available
- Adds only 3,100 lbs. to grader (12' model)
- Free factory installation (see ordering info)
| MODEL | 2012 (A) | 2014 (A) | Specifications are intended to indicate size, type, and quality of unit desired. |
|---|---|---|---|
| Overall Length | 12' 6" (3.843 m) | 14' 6" (4.45 m) | The snow wing shall be the latest design and model. Materials used shall be top quality as specified to insure uniformity. DIMENSIONS: Overall length shall not exceed ________________. Cutting edge shall be 1/2" x 6" x ________ ft. AASHO punched. Overall height front and rear shall not be less than 36". |
| Moldboard Thickness | 8 gauge (2.72 mm) | MOLDBOARD:Moldboard shall be smooth rolled design. Moldboard and moldboard
reinforcement shall be constructed of not less than 8 gauge high
strength carbon steel. Moldboard shall be reinforced across the
full length by two (2) double formed box sections; the inner section
shall be overlapped by the outer section and shall be welded together
for additional strength. The top flange shall be double formed or
otherwise reinforced for rigidity. The discharge end shall be additionally
reinforced with 1/2" diameter round bar. The bottom moldboard support
structure shall be constructed of not less than 1/2" x 7" high carbon
plate, M1044 or equal, ribbed with 1/2" x 1-1/2" A-36 steel bar
and reinforced at the bolt holes with gussets. Moldboard shall be rolled to a radius of 19-1/4" ". This radius shall be consistent from toe to heel. Weight of moldboard with cutting edge shall be approximately 1200 pounds. |
|
| Moldboard Height, front | 36" (.91 m) | ||
| Moldboard Height, rear | 36" (.91 m), optional: 32" (.81 m) | ||
Cutting Edge (AASHO and carbide punched) | 1/2" x 6" x 12' | (2) 5/6" x 6" x 7' | |
(12.67 mm x 152 mm x 3.05 m) | (12.67 mm x 152 mm x 3.05 m) |
||
Average height under raised moldboard: front |
60" (1.525 m) | LIFT MECHANISM: Rear mast shall have manual height adjustment providing a minimum
of three (3) fixed positions (Optional: 30" hydraulic slide adjustment.)
and shall incorporate a safety chain to retain the push arm and
wing in the transport position. Control of wing moldboard shall be hydraulic. 3.5" diameter double acting hydraulic cylinders shall be coupled to the wing moldboard directly without the use of cables and/or sheaves. Both heel (outer end) and toe (inner end) of moldboard shall be free floating. The outer end (heel) of the snow wing shall be raised and lowered through a spring-loaded lift arm. Minimum front lift shall be 40". Minimum outer lift height shall be 104". |
|
Average height under raised moldboard: rear |
104" (2.643 m) | ||
| Push Bar | One (1) spring-cushioned telescoping with safety shear |
MOUNT ASSEMBLY: Pivot bolt shall be not less than 1-3/4" diameter Front wing post or mast shall be located ahead of tandems and behind motor grader moldboard. Wing post shall be located to permit full articulation of the motor grader in both directions with the wing in the operating or transport position. Wing post shall be positioned to provide maximum grader blade angle. Front wing mast shall incorporate a tubular slide for smooth operation. Front post shall incorporate a chain or other such device to set the lower limit of the toe of the moldboard. Wing shall be equipped with one (1) telescoping push bar, which shall be spring buffered. Buffer spring shall be easily replaceable. Push bar shall have safety shear pin. The included angle of the moldboard shall be 30 degrees at minimum position and shall be adjustable to at least 50 degrees at the extended position. The snow wing with manual rear slide shall not add more than 3150 pounds of combined weight to the motor grader. The snow wing with hydraulic rear slide shall not add more than 3300 pounds of combined weight to the motor grader. |
|
| Weight of Moldboard Only | 950 lbs. (432 kg) | 1,100 lbs. (500 kg) | |
Weight of Moldboard and Mountings |
3,100 lbs. (1,409 kg) | 3,300 lbs. (1,500 kg) | |
| PAINT: Available in all Falls standard colors. ID and WARRANTY: Unit shall be identified with a metal plate riveted to the moldboard. ID tag shall include model, serial number, and manufacturer. 12 month limited warranty. REQUIRED VALVES Specifications are subject to change without notice. | |||
Also available: Hydraulic slide adjustment (add 200 lbs.).Hydraulic push bar extension (add 150 lbs.). Ripper mounted push bar. Prices and specifications on request.