FEATURES:

• 3/8" thick auger.
• Oversized hopper opening to reduce bridging.
• Parker Torqlink TBO and Roller Stator hydraulic motors.
• Self-leveling spinner with 6 flights.
• Hopper constructed of 7 gauge stainless steel.
• Berm chute delivers flow to road shoulder.
• End plates constructed of 1/4" stainless steel.
• Right or left hand discharge.
• Auger shaft tapped to accept speed sensor.
• Direct hydraulic shaft and spinner drive.
• Full-length hinged bottom cover with Easy Latch System for easy clean-out in any weather.
• Full-length hinged top cover with 2 position flow-control gate opening for fast, one-person dumping operations.

The following specifications aredesigned to help you acquire aFalls® Direct Drive, Single Auger, Hydraulic Stainless Steel Tailgate Spreader or its equal. The dimension within the specifications are intended to indicate the size, type, and quality of unit desired.

Hopper: Shall be minimum 1⁄4" (6.35mm) stainless steel, 96" (244.m) auger trough welded to 1⁄4" (6.35mm) end plates. Internal seams to be continuously welded to eliminate corrosion pockets. Hopper shall be designed for easy auger removal. Top cover shall be one piece and hinged for “dump over” capability. Bottom cover/clean-out door shall be one piece and hinged that one person can quickly open without tools to provide easy clean out of the auger. Top cover shall have two-position opening to accommodate various end gate configurations and sanding material consistency. Top and bottom cover shall be constructed of the same material as the hopper. All covers shall have permanently attached locking handles. Anti-flow cover shall be provided over discharge opening to prevent material spillage when auger is stopped.

Auger and Drive: Auger shall be minimum 9" (228.6mm) diameter. Flighting shall be minimum 3⁄8" (9.53mm) with 6" (152.4mm) pitch. Flighting shall be welded to 21⁄2" (63.5mm) I.D.X 13⁄4" (44.5mm) O.D. steel tubing and supported by 11⁄4" (31.75mm) shaft and shall be factory adapted to accept automatic spreader controls. The helical coil shall be mono-directional capable of feeding granular material in either direction. Auger direction shall be controlled by the hydraulic connection to the auger motor. Bearings shall be 11⁄4" (31.75mm) self-aligning type with lubrication fittings. Auger drive shall be high-torque, low-speed hydraulic motor mounted directly to the auger. Auger motor shall be mounted on four (4) Lord’s CBA12-200 center-bonded grommets to compensate for misalignment due to torque and other factors.

Spinner: Shall be 18" (.457m) diameter with six (6) replacement flights formed to provide uniform material spreading with low trajectory. Spinner and flights shall be minimum .179" (4.55mm) carbon steel. Spinner shall be adjustable left and right to control spreader pattern. Spinner shall be removable and shall include a deflector shield. Spinner drive shall be direct-mounted high torque, low-speed hydraulic motor mounted directly to the spinner (optional polyurethane spinner available).

Berm Chute: Shall be included for RH dispersal of granular material.

Mounting: Shall include mounting plates, hardware, quick disconnect pins, and tailgate spill shields. Lifting slots for chain hoist shall be provided in the end plates for easy handling.

Hydraulics: Short hose kit (from auger and spinner to rear of truck) shall be provided with terminal or junction plate. Dual flow control valve for independent speed control of auger and spinner shall be provided.

Hydraulics (optional):
1. Long hose kit (from control valve to rear of truck) shall be provided.
2. Dual flow control valve for independent speed control of auger and spinner shall be provided.

Paint: Available in all Falls standard colors.

Warranty: 12 month limited warranty.

Specifications are subject to change without notice.
The policy and promise of Little Falls Machine, Inc. is continuing product improvement. Design change and structural alterations may occur without prior notice. Such changes will not sacrifice quality or product integrity.