- FEATURES
- SPECIFICATIONS
- OPTIONS
FALLS SDL DIRECT HYDRAULIC SNOW WING - Truck Rear Mount
FEATURES:
- 8, 9, 10, 11, and 12-foot cutting edge lengths.
- 3.5" diameter double-acting hydraulic cylinders.
- Nitrided cylinders for increased corrosion resistance.
- 1-3/4" wing hinge bolt.
- Trip edge or trip moldboard available.
- Equipped with Falls' exclusive Wing Lock Valve with built-in relief.
- Double-boxed wing construction eliminates twisting.
- Two (2) cylinder control for precise positioning.
- Heavy-duty construction throughout.
- Works in conjunction with Underchassis Scraper to eliminate windrows.
- Shown with optional nitrogen-accumulated hydraulic push bar extension.
| MODEL | SDL-9A | SDL-10A | SDL-11A | |
|---|---|---|---|---|
| Overall Length | 9' 6" | 10' 6" | 11' 6" | Dimensions: Overall length shall not exceed_________. Cutting edge shall be 1/2" x 6" x ________ft. AASHO punched. Overall height front and rear shall not be less than 30". |
| Overall Height, front | 30" | |||
| Overall Height, rear | 30" | |||
| Moldboard Thickness | 10 gauge hi-tensile steel, A607-50 | Moldboard: Moldboard shall be smooth rolled design. Moldboard and moldboard reinforcement shall be constructed of not less than 10 gauge high strength carbon steel A607-50 or equal. Mild steel is not acceptable. Moldboard shall be reinforced across the full length by two (2) double formed box sections ; the one section shall be overlapped by the other and shall be welded together for additional strength. The top flange shall be double formed or otherwise reinforced for rigidity. The discharge end shall be additionally reinforced with 1/2" diameter round bar. The bottom moldboard support structure shall be constructed of not less than 1/2" x 7" high carbon plate, M1044 or equal, ribbed and reinforced at the bolt holes. Moldboard shall be rolled to a radius of 16-1/2" Weight of moldboard shall be not less than ________ pounds. |
||
| Cutting Edge (AASHO Punched) | 5/8" x 6" x 9' | 1/2" x 6" x 10' | 1/2" x 6" x 11' | Mounting Assembly: Pivot bolt shall be not less than 1-3/4" diameter. All mountings shall be of the heaviest design practical. It is the desire of this specification to reduce the added weight to the vehicle without sacrificing needed strength. Rear push frame shall be minimum 6" x 4" x 5/16" wall rectangular tubing and shall be designed to attach to both frame rails of the vehicle to more adequately distribute plowing stress. Wing shall be equipped with one (1) telescoping push bar, minimum 4" diameter, that shall be spring buffered. Buffer spring shall be easily replaceable. Push bar shall have safety shear pin. The included angle of the moldboard shall be 30 degrees at minimum position and shall be adjustable to at least 50 degrees at the extended position. Rear wing post shall be equipped with a functional wing stop that will not interfere with the normal opening and closing of the passenger side cab door. |
| Push Bar | One adjustable spring-cushioned - hydraulic extension optional | |||
| Clearing Width | 60" - 90" | 70" - 100" | 80" - 110" | Lift System: The front wing post vertical beam shall be constructed of 7" x 17.6 lb. Car & Ship Channel, A-36 steel. Vertical mast shall be attached to a cross member of a minimum 7" x 5" x 3/8" wall rectangular tubing. Post shall be equipped with double acting hydraulic cylinder and shall be coupled to slide mechanism. Front lift mechanism shall provide for a minimum 18" lift. Front lift mechanism shall provide minimum of 6" float capability. Double-acting hydraulic cylinders for the front and outer lift shall be minimum 3-1/2" diameter with 2" 36 hr. salt spray chrome plated shaft. Cylinders shall be certified to twice (2X) the working pressure of the vehicle on which it is to be installed. The outer end or heel of the wing shall have a minimum of ________ inches of lift. Heel of wing shall be provided with float capability |
| Front Lift Height | 13" | |||
| Rear Lift Height | 96" | 102" | 108" | |
| Weight, wing only | 580 lbs. | 640 lbs. | 700 lbs. | |
| Weight, wing and mountings | 1550 lbs. | 1610 lbs. | 1670 lbs. | |
VALVES REQUIRED:
Two double-acting hydraulic control valves.
Specifications are subject to change without notice.
The policy and promise of Little Falls Machine Inc. is continuing product improvement. Design change and structural alterations may occur without prior notice. Such changes will not sacrifice quality or product integrity.
Options available: Trip Edge or Trip Moldboard, Nitrogen-Accumulated Hydraulic Push Bar Extension.
Full moldboard trip.
Torsion trip edge.
NitroCush™ hydraulically extendable push bar.
Prices and specifications on request.